GENSSI hero — all clear tail lights pair with bulbs for Jeep Commander (2006-2010) on white

All Clear Tail Lights Pair w/ Bulbs for Jeep Commander (2006-2010)

$146.95
Skip to product information
GENSSI hero — all clear tail lights pair with bulbs for Jeep Commander (2006-2010) on white

All Clear Tail Lights Pair w/ Bulbs for Jeep Commander (2006-2010)

$146.95
DS-COMMANDER-TAIL-ALL-CLR-PAIR-2006-2010

Free shipping to the lower 48 · Returns & refunds · Questions? Contact us

The Commander's red corner lenses read dull from a car length back, and this all-clear pair brightens that squared-off rear by day while the red 3157 bulbs keep the brake and turn readable at night. GENSSI's set is a left and right assembly for the 2006-2010 Commander, not a Liberty lamp and not a lens cover, and it goes on with the factory sockets.

Important Fitment Note: Jeep Commander XK only. The 2002-2012 Liberty uses a different tail lamp.

Fitment

YEAR MAKE / MODEL FITS
2006-2010 Jeep / Commander, all trims Yes
2002-2012 Jeep / Liberty No

Specs

  • Style: Chrome housing with an all-clear lens; polycarbonate lens with UV protection and high impact resistance
  • Bulbs: Incandescent. Bulbs included: 4x 3157 red, for the stop socket and the turn socket on each side. Sockets are not included. Move the factory sockets. Reuse the original clear reverse bulb and the original side-marker bulb
  • Sold as: Pair — left and right tail light assemblies, with four red 3157 bulbs
  • Fit: Direct replacement for every 2006-2010 Jeep Commander trim, including Sport, Limited, 65th Anniversary, and Overland. Factory sockets, no splicing

Interchange

55396459AE, 55396459AF, 55396459AH, 55396458AE, 55396458AF, 55396458AH, CH2818107, CH2819108

What's included

  • 1x Driver (left) all-clear tail light assembly
  • 1x Passenger (right) all-clear tail light assembly
  • 4x 3157 red bulbs

Installation — Jeep Commander XK (2006-2010)

  1. Raise the liftgate. On the inner edge of the lamp, beside the liftgate opening, pry out the two push-pin retainers with a flat screwdriver or a plastic trim tool.
  2. Pull the outboard edge of the lamp straight rearward until the two ball studs pop out of the plastic grommets in the quarter panel. The studs sit tight. Pull evenly and support the housing. Do not hang it from the wires.
  3. Twist each socket a quarter turn counterclockwise and pull it out. This housing has a reverse socket, a park and stop socket, a turn socket, and a side-marker socket. Sockets are not in the box.
  4. Lock those sockets into the new housing. Put one included red 3157 in the stop socket and one included red 3157 in the turn socket. Move the original clear reverse bulb into the reverse socket and the original side-marker bulb into the side-marker socket.
  5. Line the two ball studs up with the grommets and push the lamp on until both studs seat. Press the two push-pin retainers back into the inner edge.
  6. Check parking, brake, both turn signals, and reverse before you close the liftgate.

Buyer FAQ

Is this a clear cover? No. These are full left and right housings with an all-clear lens in a chrome housing. The lens is part of the assembly.

Are the sockets in the box? No. Move the factory sockets across. The box has four red 3157 bulbs for the stop and turn sockets. Keep your original clear reverse bulb and your original side-marker bulb.

Which Jeeps fit? Every 2006-2010 Commander, including Sport, Limited, 65th Anniversary, and Overland. You get one driver-side and one passenger-side assembly. It replaces 55396459AH on the left and 55396458AH on the right. The Liberty does not use this lamp.

You may also like