GENSSI hero — red and clear tail lights pair for Nissan Hardbody (1986-1997) on white

Red Clear Tail Lights Pair for Nissan Hardbody (1986-1997)

$122.95
Skip to product information
GENSSI hero — red and clear tail lights pair for Nissan Hardbody (1986-1997) on white

Red Clear Tail Lights Pair for Nissan Hardbody (1986-1997)

$122.95
DS-HARDBODY-TAIL-RED-CLEAR-PAIR-1986-1997

Free shipping to the lower 48 · Returns & refunds · Questions? Contact us

An amber and red factory lens leaves a Hardbody looking dated from the bedside, and this red and clear pair opens the turn and reverse sections while the brake stays red. GENSSI's set is a left and right assembly for the 1986-1997 single-rear-wheel D21, and the factory sockets twist in with no splicing.

Important Fitment Note: Single rear wheel only. That lamp has three sockets. A dual-rear-wheel Hardbody uses a four-socket lamp. A 1987-1995 Pathfinder uses a different housing.

Fitment

YEAR MAKE / MODEL FITS
1986-1994 Nissan / Hardbody D21, single rear wheel Yes
1995-1997 Nissan / Pickup D21, single rear wheel Yes
1986-1997 Nissan / Hardbody, dual rear wheel No
1987-1995 Nissan / Pathfinder No

Specs

  • Style: Black housing with a red brake lens, a clear turn lens, and a clear reverse lens
  • Bulbs: Incandescent. Two amber 1156 turn bulbs are in the box. The 1157 brake bulb, the clear 1156 reverse bulb, and the 194 park bulb are not included. Sockets are not included
  • Sold as: Pair — left and right red and clear tail lights and two amber 1156 bulbs. The other bulbs and the sockets are not included
  • Fit: 1986-1997 Nissan Hardbody D21 pickup with the single-rear-wheel, 3-socket lamp. Factory sockets, no splicing

Interchange

B6555-01G00, B6555-3B300, B6550-01G00, B6550-3B300, NI2800103, NI2801103

What's included

  • 1x Driver (left) red and clear tail light
  • 1x Passenger (right) red and clear tail light
  • 2x Amber 1156 bulbs

Installation — Nissan Hardbody D21 (1986-1997)

  1. Confirm the truck is a single-rear-wheel Hardbody or D21 pickup. The factory lamp has three sockets. A dual-rear-wheel truck uses a four-socket lamp. A Pathfinder uses a different housing.
  2. The fasteners are three nuts inside the bed corner, typically 8mm or 10mm. Use a socket and an extension. A Phillips screwdriver is not the fastener on this lamp.
  3. Reach in through the bedside and remove the top nut, the middle nut, and the lower nut. Support the lamp. Do not hang it from the wires.
  4. Pull the housing straight back. Twist out the three sockets: turn signal, brake and park, and reverse.
  5. Seat the included amber 1156 in the turn socket. Move the factory 1157, clear 1156, and 194 into the remaining sockets. Those bulbs are not in the box.
  6. Lock the sockets into the new housing. Line the three studs up with the bedside holes and push the lamp in.
  7. Install the three nuts and snug them so the gasket seals. Check park, brake, both turn signals, and reverse, then repeat on the other side.

Buyer FAQ

Does a dual-rear-wheel Hardbody fit? No. This pair is the three-socket lamp for a single-rear-wheel D21. A dual-rear-wheel truck uses a four-socket lamp.

Does a Pathfinder fit? No. A 1987-1995 Pathfinder uses a different housing. This pair is the 1986-1997 Hardbody and D21 pickup lamp.

What is in the box? Left and right red and clear tail lights and two amber 1156 bulbs. Move the factory sockets and the 1157, reverse 1156, and 194 bulbs. Left replaces B6555-01G00. Right replaces B6550-01G00.

You may also like