Black Amber Halogen Headlights Pair with LED DRL for Toyota Tundra 1794 Edition / Platinum (2014-2017)

Give your 1794 or Platinum Tundra a sharp, factory-style face again. This black-housing pair replaces yellowed, hazy or cracked 2014-2017 lamps with clear lenses, amber corners, halogen reflector beams and the LED daytime running light strip built into the bottom of each housing. Each lamp bolts to the factory points and plugs into the factory connectors, with no splicing.

Fitment

Specs

• Sold as: driver and passenger pair
• Housing: black, clear lens, amber corner
• Low and high beam: halogen reflector
• Daytime running light: LED, built in
• Bulbs and sockets not included; plugs, resistors and circuit board pre-installed
• Plugs into the factory connectors (no splicing)

In the Box

• Driver-side halogen headlight with LED DRL
• Passenger-side halogen headlight with LED DRL
• Plugs, resistors, circuit board and connector plate (already installed)

Interchange References

Replaces the original assemblies commonly crossed with 81150-0C100, 81110-0C100, 81150-0C101, 81110-0C101, TO2502220, TO2503220.

Installation: Toyota Tundra 1794 Edition / Platinum (2014-2017)

On the 2014-2017 Tundra you do not have to pull the full front bumper. The grille and the plastic trim under each lamp come off so you can reach the three 10 mm headlight bolts. Turn the lights and ignition off before you start.

1. Open the hood. Remove the four 10 mm bolts across the top of the grille and the two push clips, lift the grille off its grommets and release the lower tabs.
2. Remove the two 10 mm bolts in the fender liner and the push clips that hold the plastic trim under the headlight, then pull that trim off.
3. Remove the two 10 mm bolts on top of the headlight and the 10 mm bolt on the side. Rest the lamp on a soft cloth, unplug the bulb sockets and any leveling connector, and unclip the harness.
4. Move your low beam, high beam and turn-signal bulbs and sockets to the new lamp. Plug the connectors in, set the lamp on its grommets and locating tab, and start all three bolts by hand before tightening.
5. Refit the trim and grille, test low beam, high beam, LED DRL and turn signal, then aim the beams.

Frequently Asked Questions

Which vehicles do these headlights fit?
2014-2017 Toyota Tundra 1794 Edition and Platinum Crew Cab with factory halogen headlights that have a built-in LED DRL. They do not fit SR, SR5, Limited or 2018-2021 trucks, or lamps without the LED DRL. Compare your current lamps with our photos before ordering.

Is this a pair or a single lamp?
This is a complete driver and passenger pair, not a single-side lamp.

Will these fit my 2018-2021 Tundra?
No. The 2018-2021 lamp is a different part. This pair is only for 2014-2017 1794 Edition and Platinum Crew Cab trucks with halogen headlights and a built-in LED DRL.

Will these fit an SR5 or Limited?
No. For 2014-2017 the source fitment is 1794 Edition and Platinum Crew Cab only.

Are bulbs included?
No. Bulbs and sockets are not included. Move your factory ones to the new lamps.

Do I need to cut or splice any wiring?
No. Each lamp plugs into the factory connectors.

How are they installed on a 2014-2017 Toyota Tundra 1794 / Platinum?
Take off the grille and the plastic trim under each lamp, remove the three 10 mm bolts, unplug the sockets, move your bulbs over and install the new lamp. Aim the beams when you are done.