Black HID Headlights Pair without AFS for Audi A4 and S4 (2013-2016)
Free shipping to the lower 48 · Returns & refunds · Questions? Contact us
Replace faded or cracked factory non-AFS HID lamps on your 2013-2016 Audi A4 or S4 (B8.5) with this black-housing pair. Each lamp has an LED daytime running light and LED side marker, bolts to the factory points, and plugs into the factory connectors, with no splicing.
Important Fitment Note: Fits factory HID headlights without AFS / curve lighting only, on 2013-2016 A4, A4 Quattro, S4 Quattro, and A4 Allroad. Not halogen. Not AFS. Reuse your original D3S bulbs and ballast.
Fitment
| YEAR | MAKE / MODEL | FITS |
|---|---|---|
| 2013-2016 | Audi A4 | Factory HID without AFS / curve lighting. Not halogen. Not AFS. |
| 2013-2016 | Audi A4 Quattro | Factory HID without AFS / curve lighting. Not halogen. Not AFS. |
| 2013-2016 | Audi S4 Quattro | Factory HID without AFS / curve lighting. Not halogen. Not AFS. |
| 2013-2016 | Audi A4 Allroad | Factory HID without AFS / curve lighting. Not halogen. Not AFS. |
Specs
- Sold as: driver and passenger pair (two lamps)
- Housing: black, clear lens, LED daytime running light, LED side marker
- High and low beam: HID, D3S (bulbs and ballast not included; reuse your originals)
- Turn signal: PWY24W bulbs included
- Daytime running light and side marker: LED, built in
- AFS / curve lighting: no
- DOT and SAE compliant
- Plugs into the factory connectors (no splicing)
Interchange
Replaces / cross-references: 8K0941043E, 8K0941044E, AU2518105, AU2519105
What's included
- 1x driver side (left) HID headlight housing (8K0941043E)
- 1x passenger side (right) HID headlight housing (8K0941044E)
- PWY24W turn-signal bulbs (installed)
- D3S HID bulbs and ballast are not included — reuse your originals
Installation — 2013-2016 Audi A4 / S4 (B8.5)
Tools: socket set, screwdrivers, plastic trim tools, and a helper for the bumper cover. Estimated time: about 1.5 to 3 hours.
- Park on level ground, open the hood, turn the lights and ignition off, and disconnect the negative battery cable. On the 2013-2016 A4 / S4 (B8.5) the front bumper cover typically comes off so you can reach the headlight bolts.
- Remove the fasteners across the top of the bumper and grille, the screws in each front wheel well, and the bolts along the lower edge, then release each bumper corner from the fender.
- With a helper, ease the cover forward, unplug any fog-lamp or similar connectors, and set the cover on a soft surface.
- Unplug the headlight and ballast connectors, remove the mounting bolts, and lift each lamp out. Leave the factory ballast and D3S bulb with the vehicle so you can transfer them.
- Transfer your original D3S bulb and ballast to the new housing, set the lamp in place, install the bolts, and reconnect the factory connectors. Repeat on the other side.
- Refit the bumper cover and all fasteners, reconnect the battery, test the HID beams, LED daytime running lights, turn signals, and side markers, then aim the beams on a level surface.
Buyer FAQ
Will these fit an Audi A4 or S4 with AFS (adaptive / curve lighting) or with factory halogen lamps? No. These fit 2013-2016 A4, A4 Quattro, S4 Quattro, and A4 Allroad models with factory HID headlights and no AFS / curve lighting. They will not fit AFS housings or halogen lamps.
Are the HID bulbs and ballast included? No. Reuse your original D3S HID bulbs and ballast. The PWY24W turn-signal bulbs are included. The LED daytime running light and LED side marker are built into the housing.
Do they plug into the factory connectors? Yes. They bolt to the factory points and plug into the factory connectors, with no splicing. Replaces 8K0941043E, 8K0941044E, AU2518105, and AU2519105.