Black Housing Clear Lens LED Tail Lights 4pc for Honda Accord Sedan (2003-2005)
Free shipping to the lower 48 · Returns & refunds · Questions? Contact us
Faded red-and-white factory Accord tails look dated—this black housing, clear lens LED set gives the 2003-2005 sedan a sharp blackout rear with bright red LED parking and brake lights. GENSSI's Accord kit is a vehicle-specific outer and inner 4pc set with the turn signal and reverse bulbs included.
Important Fitment Note: Fits the 2003-2005 Honda Accord 4-door sedan only—not the 2-door coupe.
Fitment
| YEAR | MAKE / MODEL | FITS |
|---|---|---|
| 2003-2005 | Honda / Accord 4-Door Sedan | Yes |
| 2003-2005 | Honda / Accord 2-Door Coupe | No |
Specs
- Style: Black housing, clear lens, red LED parking / brake light, red reflectors (outer + inner)
- Bulbs: Built-in red LED parking / brake; x2 amber 7440 turn signal and x2 white 7440 reverse bulbs included
- Sold as: Black housing clear lens LED tail light set: outer + inner, left and right (4pc)
- Fit: Direct-fit black LED tails for the 2003-2005 Honda Accord 4-door sedan
Interchange
33551-SDA-A01, 33551-SDA-A11, 34156-SDA-A01, 34156-SDA-A11, 33501-SDA-A01, 33501-SDA-A11, 34151-SDA-A01, 34151-SDA-A11
What's included
- 1x Driver outer black LED tail light
- 1x Passenger outer black LED tail light
- 1x Driver inner black LED tail light
- 1x Passenger inner black LED tail light
- x2 amber 7440 bulbs
- x2 white 7440 bulbs
Installation — Honda Accord Sedan (2003-2005)
- Park on level ground, set the parking brake, switch lights and ignition off, and disconnect the negative battery cable.
- Remove the rear bumper cover: pry out the screw caps and remove the 10 mm bolts at each end, the six Phillips screws in the wheel wells, and the two plugs under the bumper, then pull both sides out and lift the cover off.
- Open the trunk and remove the trunk side trim panel behind each outer lamp. Disconnect the connectors, remove the two 10 mm bolts under the lamp and the 8 mm nuts and screws at the back, and pull the factory outer lamp out.
- Move the bracket from the bottom of the factory lamp onto the new outer lamp, line up the locating pin, seat the lamp, and fit the nuts and screws (tighten to 5 N·m). Twist the 7440 bulbs into the sockets and reconnect the plugs.
- For each inner lamp, open the trunk lid, disconnect the connectors from the lid, remove the three nuts, and lift the factory lamp out. Fit the new inner lamp with its gasket seated flat (replace the gasket if it is distorted or stays compressed), then tighten the three nuts to 5 N·m.
- Reconnect the battery, test parking, brake, turn, and reverse on both sides, and run water over the lamps to confirm there are no leaks.
- Refit the bumper cover: clean the foam, tuck the cover under the tail lights, push the sides in, then reinstall the wheel-well screws, 10 mm bolts, caps, and under-bumper plugs.
Buyer FAQ
Does this fit the Accord coupe? No. This set is for the 2003-2005 Accord 4-door sedan only. The coupe uses a different tail light.
Is this a lens cover or a full tail light? A full replacement set: outer and inner lamps, left and right, with a black housing, clear lens, and built-in red LED parking and brake lights—not an overlay.
Are bulbs included? Yes. Two amber 7440 turn signal bulbs and two white 7440 reverse bulbs come in the box. Parking and brake are built-in LEDs, so there is nothing else to buy.