Touring Style Red / Clear LED Tail Lights 4pc for Mazda3 Sedan (2014-2017)
Free shipping to the lower 48 · Returns & refunds · Questions? Contact us
Plain base-trim Mazda3 sedan tails look flat from behind—this touring-style red and clear LED set gives it a sharper LED-style signature, with lit inner trunk-lid LED lamps at night. GENSSI's Mazda3 kit is a vehicle-specific 4pc set of outer and inner lamps that replaces the factory assemblies directly and includes the wiring for the inner LED pieces.
Important Fitment Note: Fits the 2014-2017 Mazda3 4-door sedan with non-LED outer lamps that interchange with Japan-built OEM BHN1-51-160B and BHN1-51-150B. It does not fit the 5-door hatch. Factory LED outer lamps (BHN2-51-160E / BHN2-51-150E) are a different housing. Mexico-built non-LED sedans use BJT1-51-160A / BJT1-51-150A.
Fitment
| YEAR | MAKE / MODEL | FITS |
|---|---|---|
| 2014-2017 | Mazda / Mazda3 Base 4-Door Sedan | Yes |
| 2014-2017 | Mazda / Mazda3 Sedan, factory LED outer tails | No |
Specs
- Style: JDM touring-style red / clear lens with LED lighting; polycarbonate lens with UV protection and high impact resistance
- Bulbs: Incandescent + LED combination. The inner trunk-lid LED lamps connect with the included wires and tap splices to the rear parking-light feed
- Sold as: 4pc set — left and right outer lamps plus left and right inner trunk-lid lamps
- Fit: Direct replacement for the 2014-2017 Mazda3 base 4-door sedan; mounting hardware is not included
Interchange
BHN1-51-160B, B45A-51-3G0, BHN1-51-150B, B45A-51-3F0, MA2804117, MA2802112, MA2805117, MA2803112
What's included
- 1x Driver outer tail light
- 1x Passenger outer tail light
- 1x Driver inner (trunk-lid) tail light
- 1x Passenger inner (trunk-lid) tail light
- Wires and tap splices for the inner trunk-lid LED lamps
Installation — Mazda3 Sedan (2014-2017)
- Open the trunk and disconnect the negative battery cable. For each outer lamp, pull the push clips and peel the trunk side trim back until the studs are visible.
- Unplug the outer-lamp connectors. Remove the three 10 mm nuts, put painter's tape on the body edge beside the lens, and pull the lamp rearward so the pin, studs, and hook come free. Leave the harness grommet in the body so it does not fall out.
- For each inner trunk-lid lamp, pop the plastic side cover and the trunk-shield clips, unplug the connector, remove the single 10 mm bolt, and pry the lamp out from the side.
- Set each new outer lamp on the studs, tighten the three 10 mm nuts, and plug the outer connectors back in. Snap each inner lamp in, reinstall its 10 mm bolt, and plug its connector in.
- The inner trunk-lid LEDs need the included wires and tap splices on the rear parking-light feed so they light with the parking lights. Refit the trunk trim and push clips, reconnect the battery, and check park, brake, turn, and reverse.
Buyer FAQ
Does this look like a cheap cover or a real tail light set? A real four-piece assembly set: left and right outer lamps plus left and right inner trunk-lid lamps, each with a red / clear touring-style lens in polycarbonate with UV and impact protection. It gives the plain base-sedan rear end an LED-style touring signature.
Do I have to splice any wires? One short wiring step. The outer and inner lamps are a direct replacement, and the inner trunk-lid LED lamps use the included wires and tap splices to pick up the rear parking-light feed so the LEDs light with your parking lights.
Which Mazda3 years fit, and what is in the box? The 2014-2017 Mazda3 base 4-door sedan. The box holds four lamps (outer and inner, left and right) plus the wires and tap splices, matching OEM BHN1-51-160B / B45A-51-3G0 on the left and BHN1-51-150B / B45A-51-3F0 on the right.