GENSSI hero — black smoke tail lights with LED brake for Toyota 4Runner (1996-2002) on white

Black Smoke Tail Lights w/ LED Brake for Toyota 4Runner (1996-2002)

$202.95
Passer aux informations sur le produit
GENSSI hero — black smoke tail lights with LED brake for Toyota 4Runner (1996-2002) on white

Black Smoke Tail Lights w/ LED Brake for Toyota 4Runner (1996-2002)

$202.95
DS-4RUNNER-TAIL-BLACK-SMOKE-LED-PAIR-1996-2002

Free shipping to the lower 48 · Returns & refunds · Questions? Contact us

A red factory lens leaves a third-gen 4Runner looking bright across the hatch, and this black smoke pair darkens the housing while the LED park and brake board lights faster than the old bulb. GENSSI's set is the left and right lamp for the 1996-2002 4Runner, and the factory harness plugs in with no splicing.

Important Fitment Note: 1996-2002 4Runner only. A 1990-1995 4Runner and a 2003-2009 4Runner use different housings. Park and brake are the LED board. The turn signal and reverse lamp stay bulbs.

Fitment

YEAR MAKE / MODEL FITS
1996-2002 Toyota / 4Runner Yes
1990-1995 Toyota / 4Runner No
2003-2009 Toyota / 4Runner No

Specs

  • Style: Black housing with a smoke lens. Park and brake are a built-in LED board. Turn and reverse stay bulbs
  • Bulbs: Two amber 7440 turn bulbs and two 921 reverse bulbs are in the box. Park and brake are the LED board in the housing
  • Sold as: Pair — left and right black smoke tail lights, with amber 7440 turn bulbs and 921 reverse bulbs
  • Fit: 1996-2002 Toyota 4Runner, every trim. Factory harness, no splicing

Interchange

81560-35200, 81550-35240, 81560-35120, 81550-35120, 81560-35121, 81561-35121, 81550-35121, 81551-35121, TO2818105, TO2819105

What's included

  • 1x Driver (left) black smoke tail light
  • 1x Passenger (right) black smoke tail light
  • 2x Amber 7440 turn bulbs
  • 2x 921 reverse bulbs

Installation — Toyota 4Runner (1996-2002)

  1. Confirm a 1996-2002 4Runner. A 1990-1995 and a 2003-2009 use different lamps.
  2. Open the rear hatch. Each lamp is held by two fasteners on the edge facing the hatch. They take a Phillips screwdriver or a 10mm socket.
  3. Remove both fasteners. Pull the lamp rearward, then sideways, off the two locating pins. If a pin grommet comes out of the body, press it back into the quarter before the new lamp goes on.
  4. Unplug the connector. Twist out the turn socket and the reverse socket. Park and brake are the LED board in the new housing, so those sockets are not moved.
  5. Seat the included amber 7440 in the turn socket and the 921 in the reverse socket. Lock both sockets into the new housing.
  6. Plug the connector in. Set the two pins into the body grommets, then install the two fasteners and snug them.
  7. Check park, brake, both turn signals, and reverse, then repeat on the other side.

Buyer FAQ

Is the whole lamp LED? Park and brake are the built-in LED board. The turn signal is an amber 7440 and reverse is a 921. Both bulbs are in the box.

Does a 2003 4Runner fit? No. This pair is the 1996-2002 lamp. A 2003-2009 4Runner uses a different housing.

Which part numbers does this replace? Left replaces 81560-35200. Right replaces 81550-35240.

Vous aimerez peut-être aussi