Smoke LED DRL Headlights and Bumper Lamps Set for Chevrolet Silverado (2003-2006) / Avalanche (2003-2006) / Silverado Classic (2007)

Update a 2003-2006 Silverado or a 2007 Classic, or a 2003-2006 Avalanche without cladding, with a smoked-lens LED daytime running light set. You get driver and passenger headlights plus driver and passenger bumper parking lamps, each with a black housing and a built-in LED DRL bar. Bulbs are not included — reuse your factory 9005 high-beam, 9006 low-beam, and 3157A turn-signal bulbs, or install new ones when you swap the lamps.

Fitment

Specs

• Sold as: a four-piece set — a driver and passenger headlight plus a driver and passenger bumper parking lamp
• Style: black housing, smoked lens, halogen reflector headlight, LED DRL bar in the headlight and in the bumper lamp
• Lighting: reuse factory 9005 high-beam, 9006 low-beam, and 3157A turn-signal bulbs; LED daytime running lights
• DOT certified
• 12 V
• New aftermarket assemblies

In the Box

• Driver and passenger smoke LED DRL headlights
• Driver and passenger smoke LED DRL bumper parking lamps

Interchange References

Replaces original-style 2003-2006 Silverado and Avalanche and 2007 Classic halogen headlights and bumper lamps commonly crossed with 15199556, 15199557, 10366037, 10366038, 2520185, 2521185, GM2502224, and GM2503224.

Installation: Chevrolet Silverado (2003-2006) and Classic (2007), Avalanche (2003-2006) without cladding

On these GMT800 trucks the headlight sits in the fender opening and is typically held by bolts along the top of the housing, which are easier to reach after the grille is loosened. The bumper parking lamp sits in the opening below the headlight, in the bumper cover. Professional installation and beam aiming are recommended. Switch off the lights and ignition, set the parking brake, and disconnect the negative battery cable before you start.

1. Loosen or remove the grille so you can reach the headlight mounting bolts along the top of each housing.
2. Support the headlight, remove the bolts, and pull the assembly forward. Disconnect the bulbs and the LED DRL connector, then set the lamp aside.
3. Remove the bumper parking lamp from the opening below the headlight, disconnect its harness, and transfer your 9005, 9006, and 3157A bulbs (or new bulbs) into the new housings.
4. Connect the new bumper lamp and seat it in the bumper opening, then connect the new headlight, including the LED DRL plug, and bolt the housing back into the fender opening.
5. Repeat on the other side so all four lamps are replaced as a set. Reinstall the grille, reconnect the battery, and check high beam, low beam, turn signals, and both LED daytime running lights. Aim the headlights on a level surface before driving at night.

Frequently Asked Questions

Which vehicles does this set fit?
Chevrolet Silverado 1500, 1500 HD, 2500, 2500 HD, and 3500 (2003-2006), 2007 Silverado Classic (old-body only), and Avalanche 1500 and 2500 (2003-2006) without factory body cladding, with factory halogen headlights. Compare your current housings with our photos before ordering.

Will it fit an Avalanche with body cladding, or a 2007 new-body Silverado?
No. Avalanche fitment is without factory body cladding only. 2007 Silverado fitment is the old-body Classic truck, not the new-body 2007 Silverado.

Are bulbs included?
No. Reuse your factory 9005 high-beam, 9006 low-beam, and 3157A turn-signal bulbs, or install new bulbs when you swap the lamps. The daytime running lights in the headlights and bumper lamps are LED.

How is this different from the clear-lens set?
This set uses a smoked lens on the headlights and bumper lamps. Fitment, bulb types, and the four-piece layout are the same.