Euro Style Clear Lens Black Trim Tail Lights Pair w/ Bulbs for Ford Mustang (1996-1998)
Free shipping to the lower 48 · Returns & refunds · Questions? Contact us
Factory red SN95 tails look dated next to a modern euro rear end—this clear lens set with black trim gives the 1996-1998 Mustang a crisp, blacked-out look by day, and all eight bulbs are already in the box. GENSSI's SN95 pair is a vehicle-specific left and right assembly set that replaces the factory lamps directly and reuses your factory sockets and mounting nuts.
Important Fitment Note: Fits the 1996-1998 Ford Mustang V6 and GT (SN95). The 1994-1995 Mustang uses a different tail light and is not compatible.
Fitment
| YEAR | MAKE / MODEL | FITS |
|---|---|---|
| 1996-1998 | Ford / Mustang V6 & GT (SN95) | Yes |
| 1994-1995 | Ford / Mustang | No |
Specs
- Style: Black trim housing with an all-clear euro-style lens; polycarbonate lens with UV protection and high impact resistance
- Bulbs: Incandescent. Bulbs included: 6x 3157 red (parking / brake / turn signal) and 2x 3156 clear (reverse). Sockets are not included — reuse the factory sockets and mounting nuts
- Sold as: Pair — left and right tail light assemblies with 8 bulbs
- Fit: Direct replacement for the 1996-1998 Ford Mustang V6 and GT; plug and play, reuses factory sockets and mounting nuts
Interchange
F7ZZ-13405-CA, F7ZZ-13404-CA
What's included
- 1x Driver (left) euro clear tail light assembly
- 1x Passenger (right) euro clear tail light assembly
- 6x 3157 red bulbs
- 2x 3156 clear bulbs
Installation — Ford Mustang SN95 (1996-1998)
- Open the trunk. Pull the four plastic push pins around the decklid striker and lift off the hard black trim panel. Using a Phillips screwdriver, back out the nut-type plastic retainers that hold the rear carpet trunk trim on the lamp studs, then fold the liner back to expose the lamp.
- Remove the four 11 mm (7/16 inch) nuts from the studs on each lamp with a deep 11 mm socket and ratchet. Do not drop them, since you reuse them. On the driver side a plastic trim piece sits close to the outermost nut, so work around it.
- Unplug the main harness connector, then push the rubber grommet and connector out through the body hole from inside the trunk. Ease the lamp straight out of the body with a slight side-to-side wiggle.
- Twist each bulb socket a quarter turn counterclockwise out of the old lamp. Each lamp has three 3157 sockets (parking / brake / turn signal) and one 3156 socket for reverse in the lower position. Sockets are not in the box, so move them into the new lamp with the included bulbs: red 3157 in the three upper sockets and clear 3156 in the reverse socket.
- Pass the connector and grommet back through the body hole, seat the new lamp's studs in the openings, and start all four 11 mm nuts by hand. Snug them evenly with the deep socket and do not overtighten, since the housing is plastic. Plug the connector in.
- Have a helper check parking, brake, turn, and reverse before you refit the liner, nut-type retainers, and striker trim.
Buyer FAQ
Is this a cheap cover or a full tail light set? A full replacement assembly pair. Each lamp has a polycarbonate all-clear euro-style lens in a black trim housing, with UV protection and high impact resistance, and it replaces the factory red lamp outright.
Do I need to wire or splice anything? No re-wiring. The lamps are plug and play and use your factory sockets and mounting nuts. Eight bulbs are included (six red 3157 and two clear 3156), so you only move your sockets over.
Which Mustang years fit, and what is in the box? The 1996-1998 Ford Mustang V6 and GT. The 1994-1995 Mustang does not fit. You get a left and right lamp plus eight bulbs, matching OEM F7ZZ-13405-CA on the left and F7ZZ-13404-CA on the right.