GENSSI hero — all clear lens tail lights pair Honda CR-V (2007-2011) white background

All Clear Lens Tail Lights Pair for Honda CR-V (2007-2011)

$202.95
Passer aux informations sur le produit
GENSSI hero — all clear lens tail lights pair Honda CR-V (2007-2011) white background

All Clear Lens Tail Lights Pair for Honda CR-V (2007-2011)

$202.95
DS-CRV-TAIL-ALL-CLR-PAIR-2007-2011

Free shipping to the lower 48 · Returns & refunds · Questions? Contact us

A faded factory tail lens makes a third-generation CR-V look tired from behind—this all-clear lens set gives it a crisp white-out look by day, and it still lights red on the brake with red bulbs installed. GENSSI's CR-V pair is a vehicle-specific left and right assembly set that replaces the factory lamps directly, reuses your existing sockets, and needs no re-wiring.

Important Fitment Note: Fits the 2007-2011 Honda CR-V (3rd generation), all models. The 2001-2006 CR-V uses a different tail light and is not compatible.

Fitment

YEAR MAKE / MODEL FITS
2007-2011 Honda / CR-V, all models Yes
2001-2006 Honda / CR-V No

Specs

  • Style: Chrome housing with an all-clear lens; polycarbonate lens with UV protection and high impact resistance
  • Bulbs: Incandescent. Bulbs and sockets are not included — reuse the factory sockets with 2x 194 red, 2x 7443 red, 2x 7440 amber, and 2x 7440 clear bulbs (one of each per lamp). Red bulbs are needed behind the clear lens for red parking and brake color
  • Sold as: Pair — left and right tail light assemblies
  • Fit: Direct replacement for all 2007-2011 Honda CR-V models; plug and play, no re-wiring

Interchange

33551-SWA-A02, 33501-SWA-A02

What's included

  • 1x Driver (left) all-clear tail light assembly
  • 1x Passenger (right) all-clear tail light assembly

Installation — Honda CR-V (2007-2011)

  1. Open the liftgate. Pry the two small plastic screw caps off the inner edge of the tail light (one high, one low) with a flat-blade screwdriver or trim tool, holding a cloth over the paint, and set the caps aside.
  2. Remove the two mounting screws under the caps with an 8 mm socket on a short ratchet (a Phillips screwdriver fits the Phillips-recess versions).
  3. Pull the lamp straight rearward off the corner. Three plastic pop-rivet style clips hold the outer edge to the body, so lay a towel on the bumper and, if the lamp sticks, work a plastic trim tool behind the outer edge to release the clips.
  4. Twist each of the four bulb sockets a quarter turn counterclockwise and pull them out: parking / marker at the top, brake just below it, then turn signal and reverse. Free the harness from its retaining clips and set the old lamp aside.
  5. Bulbs and sockets are not in the box. Seat your factory sockets in the new housing with a quarter turn clockwise, using a red 194 in the parking / marker position, a red 7443 for brake, a 7440 amber for turn signal, and a clear 7440 for reverse.
  6. Press the harness back into its clips, line up the three clip pegs and the locating pin with the holes in the body, and push the lamp on until the clips lock. Start both screws, snug them, and press the caps back on. Check parking, brake, turn, and reverse.

Buyer FAQ

Is this a cheap clear cover or a full tail light? A full replacement assembly, left and right, with a polycarbonate all-clear lens in a chrome housing. It replaces the factory lamp outright instead of sitting over it, and the lens has UV protection and high impact resistance.

Do I need to wire or splice anything? No re-wiring. The assemblies are plug and play and use your factory bulb sockets. Bulbs and sockets are not in the box, so move your sockets over and fit 194 red, 7443 red, 7440 amber, and 7440 clear bulbs.

Which CR-V years fit, and what is in the box? All 2007-2011 Honda CR-V models. You get one driver-side and one passenger-side all-clear assembly, matching OEM 33551-SWA-A02 on the left and 33501-SWA-A02 on the right.

Vous aimerez peut-être aussi