Chrome Halogen Projector Headlights Pair for Toyota Camry LE / XLE (2010-2011)
$97.95
Skip to product information
Chrome Halogen Projector Headlights Pair for Toyota Camry LE / XLE (2010-2011)
$97.95
DS-8111006500
Free shipping to the lower 48 · Returns & refunds · Questions? Contact us
Fitment warning: These headlights fit the 2010-2011 Toyota Camry LE, XLE and Base, US-built, with factory halogen projector lamps (81110-06500 / 81150-06500). They will not fit SE (81110-06510, a different lamp) or the 2010-2011 Camry LED pair (2010-2011 Camry LED pair).
Replace faded or cracked factory halogen projector lamps on your 2010-2011 Camry LE or XLE with this OE-style chrome-housing pair. Each lamp has the projector low beam, halogen high beam and an amber side marker, and it bolts to the factory points and plugs into the factory connectors, with no splicing. Reuse your H11 low-beam and 9005 high-beam bulbs, or add new ones.
Fitment
| Years | Vehicle | Notes |
|---|---|---|
| 2010-2011 | Toyota Camry | LE / XLE / Base, US-built, factory halogen. Not SE. Not factory LED. |
Specs
- Sold as: driver and passenger pair
- Housing: chrome, clear lens, amber side marker
- Low beam: H11 projector; high beam: 9005
- Bulbs not included — reuse your bulbs
- Plugs into the factory connectors (no splicing)
In the Box
- Driver-side halogen projector headlight
- Passenger-side halogen projector headlight
Interchange References
Replaces the original assemblies commonly crossed with 81110-06500, 81150-06500, TO2502191, TO2503191.
Installation: Toyota Camry LE / XLE (2010-2011)
On the 2010-2011 Camry the bumper cover is loosened or removed, along with the inner fender liner, so you can reach the headlight bolts. Work with a shop manual for your year. Turn the lights and ignition off, disconnect the negative battery cable, and wait a few minutes before unplugging the lamp.
- Open the hood. Remove the fasteners across the top of the bumper and the screws in each wheel well, then loosen or remove the bumper cover as needed.
- Peel back the inner fender liner to reach the remaining headlight bolts.
- Unplug the headlight connector, remove the mounting bolts and lift the lamp out.
- Transfer your H11 and 9005 bulbs if you are reusing them. Set the new lamp in place, start the bolts by hand, tighten them evenly, and reconnect the factory plug.
- Refit the liner and bumper, reconnect the battery, and test low beam, high beam and turn signal before you drive. Aim the beams after installation.
Frequently Asked Questions
Which vehicles do these headlights fit?
2010-2011 Toyota Camry LE, XLE and Base, US-built, with factory halogen projector headlights. They do not fit SE or factory LED lamps.
Is this a pair or a single lamp?
This is a complete driver and passenger pair, not a single-side lamp.
Will these fit a 2010-2011 Camry SE?
No. SE uses a different lamp (81110-06510). This pair is 81110-06500 for LE, XLE and Base only.
Are bulbs included?
No. Reuse your H11 low-beam and 9005 high-beam bulbs, or add new ones.
Do I need to cut or splice any wiring?
No. Each lamp plugs into the factory connectors.
How are they installed on a 2010-2011 Toyota Camry?
The bumper cover is loosened or removed, along with the inner fender liner, so you can reach the headlight bolts. Then unplug the lamp, transfer your bulbs if you are reusing them, install the new lamp and aim the beams.